Tutorials

BGP4

OSPF

RIPv2

PPP

Router Labs
Home
· Ethernet Back to Back
· · 2 Routers   NEW IPv6
· · 3 Routers IPv6
· · 3 Routers Triangle   NEW IPv6
· · 4 Routers
· · 4 Routers Square
· · 4 Routers Star
· · 5 Routers
· Ethernet Dynamips Switch
· · 2 Routers
· · 3 Routers
· · 4 Routers
· Ethernet Cisco Switch
· · 2 Routers
· · 2 Routers + 2 Swtiches
· · 3 Routers
· · Router on a Stick
· Frame Relay
· · 3 Routers Hub and Spoke
· · 4 Routers Hub and Spoke
· · 3 Routers Point to Point
· Serial Lines
· · 2 Routers
· · 3 Routers
· · 3 Triangle
· · 3 Triangle + One
· · 4 Routers
· · 4 Square
· · 4 Square with Cross
· · 4 Star
· · 5 Routers
· · 5 Routers Circle
· · 6 Square
· Training
· · 4 Router Basic Lab

Routing Documentation

Cisco Adminstrative Distance

Juniper Protocol Preference

Well Known Multicast Groups

RFC Overview

Cisco Documentation

IOS

IOS-XR / CRS1

Switches

Router

Security

Dynamips / Virtualization

Cisco Simulator
Cisco Simulator
Cisco Simulator Blog
Dynamips Configuration Generator
Dynagen - The Dynamips Configuration Generator
Dynamips / Dynagen Tutorial
VMware Virtual Server
QEMU Proccessor Emulator

Other CCIE Sites

Anthony J. Sequeira CCIE Page

Mr. Configure

Configuration 4 Routers Frame Relay Hub and Spoke

Loopback Addresses:

R1 172.17.0.1 255.255.255.255
R2 172.17.0.2 255.255.255.255
R3 172.17.0.3 255.255.255.255
R4 172.17.0.4 255.255.255.255

Network Addresses from Network
192.168.100.0 255.255.255.0

R1 Serial 1/0.14 192.168.100.1/30
R4 Serial 1/0.14 192.168.100.2/30

R1 Serial 1/0.123 192.168.100.9/29
R2 Serial 1/0       192.168.100.10/29
R3 Serial 1/0       192.168.100.11/29

The lab uses the Cisco 7200 routers. If you want to use other routers the configuration should work also. Please make sure you have the same interfaces in your simulated router.

The lab has four routers connected via the serial interfaces S1/0. On Router 1 all Frame Relay connections are on subinterfaces of interface serial 1/0. The DLCIs are shown in the diagram.

In the basic Frame Relay lab you can ping R2 and R3 from R1, but not R2 from R3. This is normal for Frame Relay.

The telnet password is "network", the enable secret is "routing".

Network File 4 Routers Frame Relay Hub and Spoke
Configuration no inverse arp: R1 R2 R3 R4

Lab with 4 Routers Frame Relay Hub and Spoke

Certification

Cisco
CCNA
CCNA Security
CCNA Wireless
CCNA Voice
CCDA
CCNP
CCNP Wireless
CCDP
CCIP
CCVP
CCSP
CCIE Routing & Switching
CCIE Service Provider
CCIE Voice
CCIE Security
CCIE Storage
CCIE Wireless
CCDE

Juniper
JNCIA-M
JNCIS-M
JNCIP-M
JNCIE-M

Contact


Routerlabs.de is not sponsored by, endorsed by or affiliated with Cisco Systems, Inc. Cisco©, Cisco Systems©, CCNA©, CCDA©, CCDP©, CCNP©, CCVP©, CCSP©, CCIE©, CCDE©, CCSI© and the Cisco Systems logo and the CCIE logo are trademarks or registered trademarks of Cisco Systems, Inc. in the United States and certain other countries. All other trademarks are trademarks of their respective owners.
Bookmark and Share